Madison Motorsports
Ready for Hyper Fizzle! - Printable Version

+- Madison Motorsports (https://forum.mmsports.org)
+-- Forum: Madison Motorsports (https://forum.mmsports.org/forumdisplay.php?fid=3)
+--- Forum: Lounge (https://forum.mmsports.org/forumdisplay.php?fid=6)
+--- Thread: Ready for Hyper Fizzle! (/showthread.php?tid=677)

Ready for Hyper Fizzle! - .RJ - 07-09-2004

Fresh set of XP8's

[Image: wNDY3ODQ4NnM0MTNkZmQzMXk1NDE%3D.jpg]

Advan A032R's... For Sporty Drive (Its on the tires! Wink )

[Image: wNDY3ODQ0NnM0MTNkZmQzMXk1NDE%3D.jpg]

Rollbar Padded and Camera mount in

[Image: wNDY3ODQxNnM0MTNkZmQzMXk1NDE%3D.jpg]

Evo 2 and steering wheel Bling. I picked up some Corbeau seat mounts for realy cheap - (floor mounts, no sliders) and took them to Piper Motorsport in Manassas to have the floor mount drilled for the side mount seat brackets. They had to cut and (tig) weld my side mount brackets to fit on the base - and it came out fantastic. I will probably go back there for any fab work I need.

[Image: wNDY3ODQyNnM0MTNkZmQzMXk1NDE%3D.jpg]

Wash your whip, y0!

[Image: wNDY3ODQwNnM0MTNkZmQzMXk1NDE%3D.jpg]

Figure out how the fuck all this shit is going to fit in the car.....

[Image: wNDY3ODQ1NnM0MTNkZmQzMXk1NDE%3D.jpg]

Sweet!

[Image: wNDY3ODQ3NnM0MTNkZmQzMXk1NDE%3D.jpg]

Who needs lowering springs wheen all you need is just lots of heavy shit? I'll sell some 100lb JDM lowering rocks and make a fortune.

[Image: wNDY3ODQ2NnM0MTNkZmQzMXk1NDE%3D.jpg]

RJ - resident pic whore

- Mike - 07-09-2004

My car is loaded in the gayrage here.

How did you attach your padding? I don't spoit any zip-ties.

- .RJ - 07-09-2004

The SFI padding comes with adhesive on the back side, using zip ties on it can actually make it tear.

- Sijray21 - 07-09-2004

nice, can't wait to get there sat morn.

didn't take out the rear seats?

- JackoliciousLegs - 07-09-2004

yah, why rear seats?

- JackoliciousLegs - 07-09-2004

oh, and i request ride along...

- Feersty - 07-09-2004

When are you going to go back to amber corner lenses?

- Sijray21 - 07-09-2004

i like the clear corner lenses, but i also see that ur missing a valve stem cap Wink

- EGlovr - 07-10-2004

lookin good. lookin forward to seein the vid...

- white_2kgt - 07-10-2004

.RJ Wrote:The SFI padding comes with adhesive on the back side, using zip ties on it can actually make it tear.

I don't think a chain saw could make that stuff tear. I put a zip ties on each end just to be sure, esp where the pipe bends.

-c

- .RJ - 07-11-2004

white_2kgt Wrote:I don't think a chain saw could make that stuff tear.

My $4 pocket knife that I used to cut it must be hot shit then! Wink

- Evan - 07-12-2004

mine has tears where the zipties are

- white_2kgt - 07-12-2004

Evan Wrote:mine has tears where the zipties are

Interesting. The stuff I have is hard as a rock. I used a hack saw to cut shorter pieces. 6months and no cracks/tears at the ties.

-c

- Evan - 07-12-2004

Mine is as hard as a rock too, thats exactly why i think its tearing at the zip ties, there is no give so it just rips

- Mike - 07-16-2004

my jungle gym arrived today Smile

$50 shipped by greyhound from upstate ny. took 1 day.

- Feersty - 07-16-2004

What company did you get it from :?:

- Mike - 07-16-2004

Feersty Wrote:What company did you get it from :?:

little dykes.

- Feersty - 07-17-2004

MichaelJComputer Wrote:
Feersty Wrote:What company did you get it from :?:

little dykes.

tight

- Dragon - 07-19-2004

Feersty Wrote:tight
The same could be said about Evan's and Maeng's moms a few years ago, but after whoring themselves out to the club you could drive a mack truck up that shit.

- Feersty - 07-19-2004

Damn I am so ambiguous.